Hong Kong Plasticity Conference

The 2013 Plasticity conference will be held in Hong Kong in early June, which will focus on the plastic waste problem. The first conference was held on United Nations Sustainable Development Forum in the same term last year.

This conference will be held on June 6. It will explore the solution to the problem of waste plastics. The keynote speakers include Lu Gonghui, the deputy director of Hong Kong Environmental Protection Bureau, and Mike Biddle, founder of plastic recycling enterprise MBA in California and winner of Gothenburg Award for Sustainable Development.

This forum is organized by non-profit organization, Ocean Recovery Alliance, which has offices in California and Hong Kong. The focus of this league is problems of marine pollution, including waste plastics. The American Chemistry Council is also the partner support of this conference.

“By 2013, 40% of the world’s sea surface is covered by some form of floating plastic garbage, which is thought-provoking. More and more companies and organizations are paying attention to the solution to plastic waste problem”, said the organization.

The event will also include the speech of Bayer Material Science and Taiwan Plastic Industry Technology Development Center.

The sponsor said the major intent of this conference is to collect retailers, policy makers, manufacturers and other personages of all circles to discuss the problem.

Plastic Molding Company

The plastic industry is one of the earliest invested businesses after the economic reform and open policy in China. The current decade of the 21st century, the development of the plastic industry and the foreign investments in China, where has gradually introduced into new technology for plastic mold and manufacture process. They make China growing with the mature technology of plastic mold and production capability. In recent years, variety of large fairs of plastic moulds and products were held at Shanghai and Guangzhou year by year. Those fairs successful attracted world wide¨s attentions with excellent technology and low-cost plastic mold and plastic production. That is a representative proof. 
        As a result of mature plastic mold and plastic production technology, the more and more international famous manufacturer came to China and invested to set up factories. So China went by the name of the world factory. The manufacturers from all over the world are much interested in Chinese mature plastic mold and plastic production, but it is not easy to find appropriate cooperative factory for medium and small scaled overseas corporations. They must consider the problems such as the expense of the personnel¨s business trip, the difficulty of language communication and the cooperation production quality. Therefore, lots of manufactures can not make production successfully. It is also difficult to reach the quality standard or to reduce the production cost for the manufacturers that have already made the production in China. 
        As a result of the same cultural background and language between China and Taiwan, in the initial period, Chinese plastic mold technology and plastic production manufacture flow were deeply affected by Taiwan. Taiwan¨s excellent mold technology and plastic production manufacture were acknowledged by the whole world in the last century. Sincere Tech mold. is a plastic molding company which has an excellent mold engineer and sale team from Taiwan. Each engineer in Moly-Mold passed through the government¨s technical examination, and also have technical certificate awarded by the government. They have abundant practical experience in mold technology and plastic production manufacture. And they can provide high-quality production references upon requests of customers.
        Many companies always emphasize their scale and equipment on facing to customers, but they neglect that production should be taken the human as the center. According to engineer particular characteristic, Moly-Mold can provide each visitor on the website with some important messages that are how to deal with customers¨ case and how to control product quality in the whole manufacture process. Please each to look through our website has the patience to visit our homepages. We hope our website can provide you with a message about the comparative professional the plastic mold manufacture and production technology.

PP Injection Molding

Throughout 2008 the domestic PP market, the overall PE with similar, but also from the initial price has experienced a smooth, and then start a slow market, and then prices skyrocketing, and then to the market gradually cooling, the sharp reversal of collapse, and finally to the vulnerable process. PP injection molding the first three months of the market has been in the doldrums of the state, approaching the price of pellet powder, the market turnover is very bleak. To the market to start in mid-April, the upstream crude oil prices continue to climb, propylene ferocious price rise, because the cost pressures, petrochemical manufacturers continue to push up prices, market speculation traders warm gradually rising to the May and June were the market price of PP have been had risen to an unprecedented high level, but the market did not fully follow up the High prices, the reaction to the market turnover has not unprecedented amplification, so this wave of market can only go so far, prices in mid to late July has begun, vibration downlink and continued until September; until October, the international financial crisis to the global impact has unlimited zoom, crude oil dropped sharply, the domestic PP market could not escape a fall unprecedented shrinkage of market demand, petrochemical factory inventories high, prices have diving, exacerbated traders panic mentality, PP injection molding market prices plummeted, until the late November only to stabilize the price bottomed, but the rebound is not the strength to the market is still low in mid-December concussion . Center for China’s chemical market analyst network that: In view of the current form of the domestic economic downturn and lower reaches of real estate, automobiles and household appliances, such as frozen products industry are still in the period 2009 PP cannot be optimistic about the market, or to vulnerable main concussion

Injection blow molding

plastic bottle molding Medicines are the largest production and sales of medical plastic products. With the rapid development of the domestic medical industry, the domestic consumption of medicine bottles will show substantial growth. In this regard, the domestic equipment manufacturers should be as hollow as an opportunity to grasp the development trend of plastic bottles, research and development of new high-performance, high-performance bottle molding equipment, and strive to shorten with the international advanced technology and equipment gaps.

The main molding equipment

Plastic bottle blow molding equipment, according to shape in different ways, mainly divided into three types: extrusion blow molding machine, injection blow molding machine, as well as to “squeeze – la – blow” or “Note – la – blow” molding machine. Extrusion blow molding and injection blow molding machine is mainly used for production of medicinal small plastic bottles, to “squeeze – la – blow” or “Note – la – blow” molding machine is used in the production of large bottles. At present in China, Applied Extrusion blow molding and injection blow molding machine manufacturing enterprises of plastic bottles up to.

Extrusion blow molding machine

Extrusion blow molding machinery (including the blow mold) and a lower cost, such as forming the same product, blow molding machinery, injection molding machines cost about 1 / 3 or 1 / 2. At the same time, production costs are also low. As the parison is at a relatively low pressure through the extrusion die molding and low pressure (mostly 0.2 ~ 1.0MPa) under Inflation, and therefore less residual stress in the product, and the resistance to tensile, impact, bending and the environment high performance for various contingencies, with good use of the performance. As the blow mold cavity block only by composition, so by simply adjusting the nose or the extrusion die exit gap conditions, the body can change the bottle wall thickness. In addition, because blow mold can be set to slide at the end of the module, so the bottom of the bottle-shaped body of a larger design flexibility. Extrusion blow molding the shape can be complex, irregular and the overall style of the product, and therefore more suitable for forming HDPE, PP raw materials for hard plastic bottle.

Injection Blow Molding Machine

Injection blow molding machine mainly used for processing of HDPE, PP raw materials for medicine bottles. Injection blow molding equipment, using a small plastic bottle was generally welcomed by pharmaceutical companies. As the injection blow molding of bottles in the molding process, the device can be injection nozzle bottle of injection molding, thus ensuring the accuracy of bottle; followed by a bottle blow molding machine configured mandrel body, the guarantee of the plastic bottle body shape dimensional accuracy.

Injection blow molding can be used a medicine bottle-step two-station or 3-station injection blow molding machine processing. As the two-station injection blow molding machine the lack of a dedicated off bottles and cooling stations, it is difficult to achieve fully automatic counting packaging, resulting in production efficiency was less than 3-position. Thus, in actual production use more of a three-station machine. The aircraft’s three stations to 120 ° angle into the distribution of an equilateral triangle, the first station for the injection molding station, the second station for the blow molding station, the third station for the off bottles and cooling stations. Three-station can be run simultaneously, producing high efficiency, short cycle can be connected with the conveyor automatic counting packaging, truly the whole process of production of pharmaceutical plastic bottle with the staff of the “no contact” order to ensure product cleanliness. Injection blow molding machine could not be forming the shape of complex products, and the shape of the bottle most of the smaller volume (usually 10 ~ 300ml). However, injection blow molding bottle bottle flatness high sidewall thickness uniformity, in particular, between the bottle and the bottle has good sealing performance can reach to prevent the plastic bottle of medicine and external gases of volatile gases to the bottle penetration performance requirements, which makes this bottle in full compliance with the special requirements of pharmaceutical packaging. State Drug Supervisory Authority as early as in the “Ninth Five Year Plan” period on the proposed use of injection blow molding method of producing high-quality plastic bottles. At present, China imported from abroad medicine bottle injection blow molding production lines up to more than 40, with a total production capacity of about 700 million / year.

“Note – la – blow” molding machine

“Note – la – blowing” PET, PP bottle (for filling liquid medicines) machine is divided into two kinds of one-step and two-step models. One-step model is the parison injection, heating parison, the tensile parison and blow molding processes such as product ejection device in the same row for the efficient equipment. According to molding processes, one-step model is divided into three stations (Aoki of Japan, represented by solid machine) and 4-position (in Japan’s precision machinery as the representative) two kinds of machines. The main difference between the two is: “3-station” refers to the injection with the heated parison parison in a process completed, “4-station” refers to injection with the heated parison parison in the two processes to complete. One-step model does not cause secondary pollution products, and a good product identity. Despite higher prices, but to reach the high cleanliness requirements bottles in recent years, the domestic pharmaceutical companies more inclined to use the one-step “Note – la – blow” bottle molding machine. To this end, some equipment manufacturers in the domestic absorption of foreign advanced technology and intensify the development on the basis of foreign equipment could be replaced by one-step models, and have achieved some results.

Two-step model refers to the injection and stretch blow molding process by an independent two machines separately. The first step: from a common injection molding machine injection molding tube, head tube of the bottle part (bottle, screw) had completed its forming; the second step: The tube on the honeycomb heater or automatic cycle of heating on the heat conveyor thermostat, and then moved to the stretch blowing process using compressed air to blow molding. Than the flat bottle, seal well and fast product development, mold fees and costs, lower prices are “two-step” models of advantages, but due to injection blow molding tube and the step-wise, the product identity is poor, and easy to pass pollution, difficult to check by bacteria.

R & D direction

Plastic bottle forming machine up to other hollow plastic molding equipment, specifications of small, fast, high precision and high efficiency. The main direction of its R & D high-speed, high efficiency, energy saving, environmental protection and adaptive quality control.

All-electric one-step “Note – la – Blow” Blow Molding Machine

The recent development of a high response AC servo motor-driven dosing pumps energy-saving systems, injection molding machine has been successfully applied. Similarly, injection blow molding, “Note – la – blowing” plastic bottle molding equipment of the main system power drive can also be portable such systems. The system pressure and flow through precise closed-loop control of servo motor to achieve the energy requirements of the implementing agencies the best matching and automatic adjustment, so as to achieve energy efficiency, improve performance and reduce environmental pollution multitude of purposes.

All-electric one-step “Note – la – Blow” Blow Molding Machine for its precise location, speed, no vibration, high self-cleaning as well as the advantages of high efficiency, high-performance plastic bottle molding machine into the development of hot. The key to development of aircraft types is to achieve turntable body clamping preform molding, stretch blow molding and injection-locking mechanism simultaneously plasticizing institutions of all-electric drive. All electric molding preforms and stretch blow mold body simultaneously locking mechanism design, refer to the all-electric injection molding machine clamping. For the all-electric injection of plasticized bodies, can be completely copy all-electric injection molding machine plasticizing bodies. It can be said, with the all-electric injection molding machine mature technology, which is developing electric-step “Note – la – Blow” Blow Molding Machine is not very great difficulty.

At present the domestic market all-electric one-step “Note – la – Blow” Blow Molding Machine, with Shanghai Machinery Co., Ltd. Ace must be represented by models developed by ASB-15N/10E. The machine uses closed-loop servo system, than the original hydraulic system greatly improved the stability of control, saving up to 40% and a change of hydraulic transmission fluid oil (hydraulic system valves, piping, etc. prone to leak, the use of age is even worse than the old equipment) on the environment, product contamination.

High-speed, high-quality PET, PP preform injection gasoline-electric composite body

The performance of injection plastics sector is directly related to the quality of preforms. Reciprocating screw injection of common plastics, as before and after the plasticizing quality and inconsistent, leading to inconsistent quality preform; and also because the two can be made between injection and plasticizing the same time, reducing production efficiency. Note the use of composite plastics extrusion injection system (to be plasticized with the injection of two kinds of functions from the conventional one component is divided into two parts, namely, an independent servo motor-driven extruder screw plasticizing and hydraulic plunger independent injection, both of the Inter-Noninterference), then to stabilize the PET, PP melt axial temperature and thus to achieve consistency of quality plastics, but also greatly enhance productivity.

Improve the forming rate and yield

Improve production efficiency is the domestic pharmaceutical packaging container injection blow molding equipment, the key to development. Vinda Jiangsu Machinery Co., Ltd. successfully developed the domestic first-step three-station injection blow molding machine, has in recent years is based on 100 production lines each year the size of rapid development. Use of Ouida’s MSZ60L models, the production 30ml × 12 cavity typical of conventional plastic bottles production cycle of only 10S. Zhangjiagang Green Central degradation of complete sets of equipment Co., Ltd to absorb European NOVVAPAX, BEKUM of the technology, has developed solid particles suitable for the production of medicinal polyolefin bottles of high-performance 3 station injection blow moulding machine, the shortest production cycle up to 8s. Machine dual-link mechanical protection, turntable with the opening and closing movements synchronous operation mode, greatly shorten the cycle; use of plasticizing screw extruder, screw aspect ratio increased to meet the transparent PP, PE, PS, PC and other hollow products process needs; preform temperature uniformity, product unparalleled line; with a single beam clamping structure, convenient and quick replacement of mold; machines simple shape is conducive to purification, in line with GNP specifications. Panan triple Pharmaceutical Packaging Co., Ltd. for the production of generic pharmaceutical plastic bottles technical problems, has created a unique high-pressure gas thermostat technology. The technology uses electromagnetic speed control system to replace the inverter system, reducing the machine size, reduced power consumption, and improved use of equipment performance and product quality.

Development of high-performance mold

Although in recent years, many domestic enterprises in the “Note – la – blowing” equipment to spend more energy and money, so that equipment has been reach or approach international advanced level, but because of neglect and efficient accompanying “Note – la – blowing” mold development, and therefore can not play its due role in equipment. This is a bottleneck restricting development of the industry. For relevant domestic enterprises, in order to develop a high level of “Note – la – Blow,” Die, you must use an advanced computer-aided engineering (CAE) technology to the “Note – la – blowing” process simulation, which avoided by experience, trial and error and by way of amending the blindness brought about the end, the mold material, mold cavity ratio of the different blowing Zhang, hot runner nozzle structural design, as well as temperature control, etc. have access to the most optimal results. Multi-layer co-extruded hollow plastic bottle molding machine

Multi-layer composite bottle has to avoid the light transmission and to prevent the infiltration of gases such as C02 performance, to meet certain require special storage conditions required for bio-engineering drugs, has become a major pharmaceutical packaging market, one of the products. For example, the 3-layer co-extruded plastic bottles (the most outer layer of the PA material, the middle layer of PET material, the inner layer of PC material), with good transparency and tightness can be isolated from moisture and oxygen, not only for routine blood products, such as human serum albumin and protein, collagen fibers and other products directly to packaging, but also can be used as a variety of bio-engineering drugs, such as interferon, monoclonal antibody drugs, a variety of packaging materials.

Multi-layer co-extrusion Blow molding machine bottle blow molding machine and other than the greatly increased complexity, especially in the nose design. Current research and development for the aircraft types, the main focus on the following three points: (1) to study the use of a certain range of co-extrusion head to meet the needs of different materials, different layers, and head diameter and other requirements. The nose is a multi-layer co-extruded hollow plastic molding machines of the “heart”, its performance should reach: control at every level to achieve the best condition to achieve the perfect circle and lateral material distribution; can not influence the distribution of the processed material change a wide range of plastic raw materials. Spiral mandrel composite systems are highly adaptable, multi-layer co-extruded nose should be the priority to the use of the system. (2) research portfolio of packaging systems, which can be customized according to different materials which might allow the number of combinations of nose. (3) research-based mechanical procedures in order to determine the number of molding stations, the production speed and size of product design platform.

Conclusion

Medicine bottles are the largest production and sales of medical plastic products, but also a rapid growth of large medical plastic products. The product is inseparable from the production of high-performance, high-performance hollow molding equipment (including mold). As the domestic Blow Molding Equipment, compared with foreign equipment, there is not a small gap, therefore, the domestic hollow plastic molding equipment manufacturers can only grasp the development trend of the bottle, research and development of new plastic bottle molding equipment, in order to gradually narrow the gap with foreign manufacturers , and in the market with rival.



custom injection molding service

China Plastic Mold Company is a professional custom plastic injection molding service company, offering customers the best plastic injection moulding products.

First we will share you some plastic injection molding sort:

Use mold-volume business with low cost, easy processing quality control characteristics, particularly applicable to mass production. 
Die stamping molds and a plastic mold. Stamping Die processing methods can be classified in accordance with, can be divided into blanking die punching, bending die, die tensile, shear Die, Die flanging, such as plastic mold. Generally used as steel and other metal materials processing.
plastics Processing die by the type of plastic can be divided into thermoplastic and thermosetting plastic mold two categories. 
Thermoplastic is used in the plastic injection mold. 
Heat Solid Mold : 
Die by the press on a fixed mode can be divided into : 
1. Mobile Die: the machine is not fixed, mold filling, open mode, and plastic products removed from the mold, both in the machine outside. This mold structure, creating simple, low efficiency, high labor intensity, apply only to small pieces of the Batch processing.
2. Fixed Die: fixed on the machine, throughout the process, loading, or mold, shape, open mode and the introduction of plastic products, etc. on the machine.Easy-to-use, low labor intensity, high efficiency, mold structure more complex, mainly for mass production. 
According to plastics molding method Categories : 
1. Pressure mold: plastic installed in the heated indoor cavity or feeding, then pressurized. Suppress directly on the plastic cavity pressure. Such Mold Filling Room in the general cavity is one.
2. Transmission mode: Filling in plastic indoor heated become viscous flow state, the plunger under pressure to make cladding material after injection system into full closure of the cavity. 

Go to home page by click here

Blow Molding Parts

We are a world class blow molding parts leader in the design and manufacture of custom blow molds & blow molded parts. Leading the blow molds industry for more than a quarter century, we have set the standard for Design Innovation of blow molds, Precision Blow Molds Manufacturing, and Customer Support.

We Design Blow Molds, Quick Change Blow Molds, Blow Molds Manufacturer, variety of Blow molds, 2D and 3D design for Blow Molds using solid modeling, Blow Molds of plastic bottles, we supply a wide variety of Blow molds

Our Blow Molds are designed and manufactured with state of the art engineering systems and blow molds manufacturing equipment. We have been building blow molds since 1978.